Информацията от тази тема е взета от източник:
1. Straight buildings
Generally speaking, every baseplate is 32 studs deep. The width is variable with straight buildings, always being a multiple of 8 studs. A common used width is 16 studs wide. The connection points, pavement, walls etc. will then have the following sizes:
Whether your building is 8 studs wide or 64 studs wide, the sizes in depth are always the same. That way the Technic bricks with hole will always align and allow for the buildings to be attached to one another through the use of Technic pins.
2. Corner buildings
In the case of a corner building, you’re dealing with two connecting points at a 90 degree angle of each other. Therefore, your baseplate will always have to be 32 x 32 studs. Of course you can make the full building larger by attaching straight buildings forming a continuous whole at either side, but the corner module must be 32 x 32:
3. Variation in depth sizes
If you look at a real-life (old) street, you will see that not all buildings align in a perfectly straight line: some jut out a bit, others fall a little further back. If you put a number of CCMS buildings in a row, this method of alignment will give you the best result. As long as you leave the Technic bricks in the right position for connecting, you’re free to place your front and back wall at will. This might result in something like this:
Keep the variation in mind, because of your side wall. In some cases, part of your side wall will be visible. So if you were planning to omit your side wall, or make one out of all the colors you won’t be needing for the front and back walls, make sure that at least the edge of the side wall that juts out is made of a color that fits with the rest of the building.
I myself always build an entire side wall if I know the building is going to end up in a combined layout with other builders: because you don’t quite know what will end up next to you. For all you know you might end up next to a construction side, leaving your side wall entirely exposed.
The last point I wish to address is height. In terms of height, you’re basically free to do whatever you want. Make it as tall or as low as you wish. One floor 6 bricks high, eight floors 12 bricks high each, everything is possible. Do keep in mind though, that if you’re making a very tall building, your side walls will definitely be visible. So make it into something exciting featuring windows or something, so it’s not just one boring, flat wall. Do take care that you won’t have anything protruding over the edges, since you may not know how high the building next to yours might be.
Variation in height is another reason to build side walls in a matching color when your creation will end up in a combined layout: the building next to yours might be very low and you won’t know ahead of time.
Наскоро се сдобих с един употребяван сет, където е необходимо да заменя няколко липсващи/повредени части:
Rubber Band Extra Small (Square Cross Section) – черен цвят, 6 броя
Rubber Band Small (Square Cross Section) – черен цвят, 3 броя
Technic, Axle and Pin Connector Perpendicular – стар тъмносив цвят, 1 брой
Още не съм направил пълен преглед на инвентара, така че е възможно да се появят и други липси, но идеята ми е да разпитам тук на по-ранен етап, преди така или иначе да поръчам частите от Германия.
Здравейте в тази тема ще публикувам частите от които имам нужда за МОК-овете ми.
Wall Element 1X6X5 - Бял
Wall Element 1X6X5 - светло син, прозрачен
Brick 1X2X5 - Светло син, прозрачен
Брик брикове, най-вече в светло и тъмно сиво
Прозорци най-вече тези в TAN цвят
6034929: Frame 1X2X3
Може и други цветове.
Относно количествата... всичко над 1 бройка е добре дошло.